Navigation System - HDD Map Update Processes
L-SB-0148-11
December 14, 2011
HDD Navigation Map Update Process
Service Category
Audio/Visual/Telematics
Section
Navigation/Multi Info Display
Market
USA
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 255
Applicability
Introduction
Lexus models equipped with Hard Disk Drive (HDD) Navigation require a Special Service Tool and follow a unique process for updating map
points of interest and system software. Instead of individual DVDs installed into the vehicle all Map Data is uploaded directly to the HDD system.
Map Data will be released annually through the direct shipment of two Map Data DVDs to each dealership service manager. The annual Map Data
release must then be installed onto the Navigation Update Tool. Individual map updates are then loaded into vehicles with special map security keys.
These keys are available through the normal parts ordering system. Keys are loaded onto the Navigation Update Tool through a PC or TIS
Techstream unit using software found on the Technical Information System (TIS).
Follow the procedures listed in this bulletin to:
^ Identify the current version of Map Data on the vehicle and on the Navigation Update Tool.
^ Load Map Data onto the Navigation Update Tool.
^ Load map security key(s) onto the Navigation Update Tool.
^ Connect the Navigation Update Tool to the vehicle and update the Map/System Data to the latest version.
NOTE
^ In order to perform the procedures outlined in this TSIB, you MUST have completed the setup procedure in TSIB No. L-SB-0180-09, "HDD
Navigation Program Setup".
^ Before performing this procedure, disconnect all other USB peripheral and external storage devices (i.e., USB thumb drives, hard drives,
cameras, mice, etc.).
^ For additional details, refer to the "Navigation Update Tool Operating Manual" on TIS (under Diagnostic / Tools and Equipment /
Navigation Update Tools tabs, "Reference Documents").
Warranty Information
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 256
Parts Information
Required Tools & Equipment
Version Verification
Checking for Map Data Version on Navigation Update Tool
WARNING
DO NOT attempt to install Navigation Map Data prior to performing the "Navigation System Firmware Improvement" bulletin.
^ L-SB-0067-09- Generation 5
^ L-SB-0147-11- Generation 6
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 257
1. Open the Navigation Programs Installer.
2. Click Version Check on the Navigation Update Tool Main Menu.
3. Connect the Navigation Update Tool.
A. Make sure the USB cable is secured in both the PC and the Navigation Update Tool USB ports.
B. Confirm that the Navigation Update Tool is powered correctly.
C. Turn power ON.
D. Press Continue.
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 258
4. Compare the CDDB version with the CDDB version shown on TIS.
Checking Map Data Version on Vehicle HDD Navigation System (Generation 5)
1. Turn vehicle ignition ON (engine OFF).
2. From the multi-information display, press I Agree.
3. Press the MENU button.
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 259
4. From the multi-information display, press HDD Data.
5. Compare the Map Data version on the Navigation System to that on the Navigation Update Tool.
Checking Map Data Version on Vehicle HDD Navigation System (Generation 6)
1. Turn vehicle ignition ON (engine OFF).
2. Press the INFO/PHONE button.
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 260
3. From the multi-information display press Map Data
4. Compare the Map Data version on the Navigation System to that on the Navigation Update Tool.
Tool Load
NOTE
There are three separate processes used to update the Map Data on the vehicle:
^ Loading the Map Data onto the Navigation Update Tool
^ Loading the Map Data security key onto the Navigation Update Tool
^ Loading the Map Data into the vehicle HDD Navigation System
1. Generation 5
2. Generation 6
If the Map version on the Navigation Update Tool is the same as shown on TIS, then go to the "Security Key Load" section in this TSIB.
If the Map version on the Navigation Update Tool is NOT the same as shown on TIS, then follow the instructions below.
Loading Map Data onto Navigation Update Tool
NOTE
Before performing this procedure, disconnect all other USB peripheral and external storage devices (i.e., USB thumb drives, hard drives,
cameras, mice, etc.).
1. Open the Navigation Programs Installer
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 261
2. Select Load Map Data on the Navigation Update Tool Main Menu.
3. Connect the Navigation Update Tool.
A. Make sure the USB cable is secured in both the PC and the Navigation Update Tool USB ports.
B. Confirm that the Navigation Update Tool is powered correctly.
C. Turn power ON.
D. Press Continue.
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 262
4. Insert Map Disk 1 into the CD/DVD-ROM drive and press Continue.
5. Allow Map Data to copy onto the PC hard drive (requires about 30 minutes).
If necessary:
^ Insert the additional Map Disk as instructed into the CD/DVD-ROM drive.
^ Allow the additional Map Data to copy onto the PC hard drive (requires about 30 minutes).
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 263
6. Verify the correct version of Map data to load onto the Navigation Update Tool.
7. Click Continue to load Map Data onto the Navigation Update Tool.
Map Data will then copy to the Navigation Update Tool (requires about 15 minutes).
8. Verify the Map Data is loaded onto the Navigation Update Tool and can now be used to update the vehicle.
Security Key Load
NOTE
^ In order to load the Map Data onto the vehicle's Navigation System, you MUST load a security key EACH time.
^ The Navigation Update Tool will hold up to ten security keys. One key is required per vehicle update.
^ Storing keys on the Navigation Update Tool is NOT recommended.
^ Map Data MUST be loaded onto the Navigation Update Tool before a Key File can be loaded.
^ Before performing this procedure, disconnect all other USB peripheral and external storage devices (i.e., USB thumb drives, hard drives,
cameras, mice, etc.).
1. Open the Navigation Programs Installer.
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 264
2. Select Load key File on the Navigation Update Tool Main Menu.
3. Connect the Navigation Update Tool.
A. Make sure the USB cable is secured in both the PC and the Navigation Update Tool USB ports.
B. Confirm that the Navigation Update Tool is powered correctly.
C. Turn power ON.
D. Press Continue.
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 265
4. Connect USB Key File and press Continue.
5. Click Load to continue.
6. Allow the Key File to copy onto the Navigation Update Tool (requires about 5 seconds).
7. Verify the Key File is loaded onto the Navigation Update Tool and can now be used to update the vehicle.
Vehicle Loading
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 266
NOTE
^ The Map Data security key MUST be loaded onto the Navigation Update Tool before Map Data can be loaded to the vehicle.
^ Prior to connecting to the vehicle you MUST disconnect the Navigation Update Tool from the PC.
^ Connect the battery charger to the vehicle prior to beginning the process to ensure constant battery voltage.
Loading Map Data onto Vehicle HDD Navigation System (Generation 5)
NOTE
Prior to connecting to the vehicle you MUST disconnect the Navigation Update Tool from the PC.
1. Connect the Navigation Update Tool to the vehicle.
A. Make sure the 1EEE1394 cable is secured in both the Navigation Update Tool and the vehicle connector.
B. Confirm the Navigation Update Tool is powered correctly.
2. Turn vehicle ignition ON (engine OFF).
3. From the multi-information display press I Agree.
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 267
4. Press the "MENU" button.
5. From the multi-information display, press HDD Data.
6. Press Map Data Update.
7. Press I Agree.
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 268
8. Allow Map Data to copy (requires about 25 minutes).
9. Press OK.
10. Disconnect the Navigation Update Tool from the vehicle.
Loading Map Data onto Vehicle HDD Navigation System (Generation 6)
NOTE
Prior to connecting to the vehicle you MUST disconnect the Navigation Update Tool from the PC.
1. Connect the Navigation Update Tool to the vehicle.
A. Make sure the 1EEE1394 cable is secured in both the Navigation Update Tool and the vehicle connector.
B. Confirm the Navigation Update Tool is powered correctly.
2. Turn vehicle ignition ON (engine OFF).
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 269
3. Press the INFO/PHONE button.
4. From the multi-information display press Map Data.
5. Press Map Data Update.
6. Press I Agree.
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 270
7. Allow Map Data to copy (requires about 25 minutes).
8. Press OK.
9. Disconnect the Navigation Update Tool from the vehicle.
No comments:
Post a Comment