Body - Bumper Component Repair
TITLE: BUMPER COMPONENT REPAIR
SECTION: EXTERIOR
BULLETIN # 172
MODELS: ALL TOYOTA LEXUS and SCION
DATE: MARCH 2009
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 337
While it may seem cost effective to repair damaged bumper components specifically impact energy absorbers and reinforcements there is no way to
certify that a repaired part will function as originally intended under all future operating conditions and subsequent collisions. Original Equipment
bumper components comply with Federal Motor Vehicle Safety Standards established under the National Highway Traffic Safety Administration
Title 49 Part 581. Therefore it is recommended to replace damaged bumper impact energy absorbers and reinforcements with genuine new original
equipment replacement parts only.
For more information on collision damage repair topics please refer to Collision Repair Information Bulletin # 161 Collision Damage Repair
Precautions and plan to attend Toyota Collision Repair & Refinish Training. Visit www.crrtraining.com for training information.Technical
Service Bulletin # SB0172-08 Date: 081222
Instruments - Compass Calibration Procedure
L-SB-0172-08
December 22, 2008
Initial Calibration of Compass During PDS
Service Category
General
Section
Pre-Delivery Service
Market
USA
Applicability
Introduction
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 338
Some 2010 model RX350 vehicles are equipped with a compass in the rear view mirror. In order for the compass to correctly indicate the direction
that the vehicle is heading it must be calibrated prior to vehicle delivery. Use the following procedure to perform initial calibration during
Pre-Delivery Service (PDS).
Warranty Information
Calibration Procedure
1. Cycle the ignition switch to the "IG-ON" position and hold the "AUTO" switch for 6 seconds until the zone number appears on the display.
HINT
Pushing the "AUTO" switch for 3 seconds turns ON or OFF the compass display.
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 339
2. Push the "AUTO" switch to select the number of the zone where the vehicle is located. See the map in figure 3 for zone reference.
3. Start the engine and push the "AUTO" switch for about 9 seconds until "C" appears on the display.
4. Drive the vehicle slowly at 5 mph (8 km/h), or less, in a circle until the direction is displayed. If there is NOT enough space to drive in a circle,
drive around the block until the direction is displayed.
Once the direction is displayed, the calibration is complete.
NOTE
^ Do NOT perform calibration of the compass in a place where the Earth's magnetic field is subject to interference by artificial magnetic fields
(underground parking, under a steel tower, between buildings, roof parking, near a railroad crossing, near a large vehicle, etc.)
^ During calibration, do NOT operate electric systems (moon roof, power windows, etc.) as they may interfere with the calibration.Technical
Service Bulletin # CRIB173 Date: 090401
Paint - Refinishing Information
TITLE: TOPCOAT SAND & POLISH
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 340
SECTION: REFINISH
BULLETIN # 173
MODELS: ALL TOYOTA LEXUS AND SCION
DATE: APRIL 2009
Customers have high expectations for automotive paint finish appearance and expect repairs to match factory color gloss and texture. Flawed refinish
appearance is a cause of concern and will likely have a negative affect on customer satisfaction and retention.
Toyota recognizes the reality of paint finish application in the shop environment. In addition to color matching and blending countermeasures to
remove paint process intrusion (dirt nibs) are necessary to achieve an undetectable finish match. This is also common in manufacturing plants when
process intrusion is encountered. Countermeasures are defined as; ultra-fine sanding to level nibs followed by polishing to a level of gloss and
texture consistent with the original finish. Technicians undertaking these tasks should review applicable technical data sheets for product process and
handling instructions as well as applicable safety information.
Topcoat sand and polish is one of many paint finish repair techniques covered in Toyota T101 and Lexus L101 Paint Finish Repair training. Please
No comments:
Post a Comment