Canada - Suspension - Shock/Strut Replacement
Bulletin
L-TCI-3086
Issue Date
December 23, 2011
Market
Canada
Title
SHOCK ABSORBER REPLACEMENT CRITERIA
Service Category
Suspension
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 32
Section
Front Suspension
APPLICABILITY:
TSB SUPERSESSION NOTICE
The information contained in this TSB supersedes TSB No. T-TCI-2364.
- Applicability has been updated to include 2008 - 2012 model year Lexus vehicles.
TSB No. T-TCI-2364 is Obsolete and any printed versions should be discarded. Be sure to review the entire content of this service bulletin
before proceeding.
INTRODUCTION:
The purpose of this TSB is to provide a quick reference to assist in making easy judgements regarding shock absorber and strut replacements.
WARRANTY INFORMATION:
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 33
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 34
INSPECTION:
NOTE:
Issue of this Technical Service Bulletin is to ensure that proper repair information is available. IT DOES NOT CONSTITUTE AN
AUTHORIZATION FOR REPAIR. Normal provisions of the formal warranty policy, as applicable, will apply.Technical Service
Bulletin # CAN-TSB3042L Date: 110928
Canada - Emissions - MIL ON/DTC P2420 Set
Bulletin
L-TCI-3042
Issue Date
September 28, 2011
Title:
MIL "ON" DTC P2420
Service Category
Vehicle Interior
Section
Meter/Gauge/Display
Market
Canada
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 35
APPLICABILITY:
INTRODUCTION:
Some 2009 - 2010 model year Lexus vehicles may exhibit a MIL "ON" condition with Diagnostic Trouble Code (DTC) P2420 (Evaporative
Emission System Switching Valve Control Circuit High) present. The charcoal canister has been updated to address this condition.
PRODUCTION CHANGE INFORMATION:
This TSB applies to vehicles produced BEFORE the Production Change Effective VIN shown.
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 36
WARRANTY INFORMATION:
REQUIRED TOOLS & EQUIPMENT:
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 37
PARTS INFORMATION:
REPAIR PROCEDURE:
1. Using ETAS Techstream, check for Diagnostic Trouble Codes (DTCs).
2. Are codes other than P2420 present?
- YES - Diagnose other DTC(s) first.
- NO - Continue to step 3.
3. Inspect VSV for proper power and ground circuits.
Perform the following checks with the Canister Pump Module Connector connected and back probe the pins to obtain the readings.
A. Check for voltage between Pin 9 (VLVB) and Chassis Ground. With IG ON, voltage should read between 9 V and 14 V.
- YES - Proceed to next step (3B).
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 38
- NO - This TSB does NOT apply - inspect and repair wiring.
B. Check for voltage between pin 8 (VGND) and Chassis Ground. With IG ON, voltage should read between 9 V and 14 V.
- YES - Proceed to next step (3C).
- NO - Vent Valve is open - proceed to step 4.
C. Using ETAS Techstream, activate the VSV and check voltage between pin 8 (VGND) and Chassis Ground.
Powertrain > Engine > Active Test > Activate the VSV for Vent Valve
- 9 V - 14 V present - This TSB does NOT apply - inspect and repair wiring.
- < 1 V present - Proceed to step 4.
4. Replace the Charcoal Canister Assembly.
Refer to TIS, applicable model and model year Repair Manual:
- 2010 ES350:
Engine/Hybrid System - Emission Control - "2GR-FE Emission Control: Canister: Removal / Installation"
- 2009 GS350:
Engine/Hybrid System - Emission Control - "2GR-FSE Emission Control: Canister: Removal / Installation"
- 2010 GS350:
Engine/Hybrid System - Emission Control - "2GR-FSE Emission Control: Canister: Removal / Installation"
- 2010 GS450h:
Engine/Hybrid System - Emission Control - "2GR-FSE Emission Control: Canister: Removal / Installation"
- 2010 GS460:
Engine/Hybrid System - Emission Control - "1UR-FSE Emission Control: Canister: Removal / Installation"
- 2010 HS250h:
Engine/Hybrid System - Emission Control - "2AZ-FXE Emission Control: Canister: Removal / Installation"
- 2010 IS250:
Engine/Hybrid System - Emission Control - "4GR-FSE Emission Control: Canister: Removal / Installation"
- 2010 IS350:
Engine/Hybrid System - Emission Control - "2GR-FSE Emission Control: Canister: Removal / Installation"
- 2010 IS250C:
Engine/Hybrid System - Emission Control - "4GR-FSE Emission Control: Canister: Removal / Installation"
- 2010 IS350C:
Engine/Hybrid System - Emission Control - "2GR-FSE Emission Control: Canister: Removal / Installation"
- 2010 IS-F:
Engine/Hybrid System - Emission Control - "2UR-GSE Emission Control: Canister: Removal / Installation"
- 2009 LS460/460L:
Engine/Hybrid System - Emission Control - "1UR-FSE Emission Control: Canister: Removal / Installation"
- 2010 LX570:
Engine/Hybrid System - Emission Control - "3UR-FE Emission Control: Canister: Removal / Installation"
- 2010 RX350:
Engine/Hybrid System - Emission Control - "2GR-FE Emission Control: Canister: Removal / Installation"
- 2010 RX450h:
Engine/Hybrid System - Emission Control - "2GR-FXE Emission Control: Canister: Removal / Installation"
- 2010 SC430:
Engine/Hybrid System - Emission Control - "3UZ-FE Emission Control: Canister: Removal / Installation"
5. Clear all DTCs using ETAS Techstream.
6. Perform the Automatic EVAP System Check and verify that no pending DTCs set.
System > Engine and ECT > Utility > EVAP System Check
NOTE
If the Automatic EVAP System Check fails to run, perform the following:
- Turn the ignition OFF.
- Turn ETAS Techstream OFF.
- Turn the ignition ON and ETAS Techstream ON and restart the Automatic EVAP System Check.
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 39
NOTE:
Issue of this Technical Service Bulletin is to ensure that proper repair information is available.
IT DOES NOT CONSTITUTE AN AUTHORIZATION FOR REPAIR. Normal provisions of the formal warranty policy, as applicable,
No comments:
Post a Comment