Canada - Entertainment - USB/Ipod Limited Compatibility
Bulletin
L-TCI-2952
Issue Date
September 8, 2011
Title:
USB/iPod NOT RECOGNIZED
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 55
Service Category
Audio/Visual/Telematics
Section
Audio/Video
Market
Canada
APPLICABILITY:
INTRODUCTION:
Some 2010 Lexus vehicles may exhibit an intermittent operation of USB/iPod(TM) device condition while in use. A newly designed Multi-Media
Interface ECU has been developed to correct this condition.
PRODUCTION CHANGE INFORMATION:
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 56
This TSB applies to vehicles produced BEFORE the Production Change Effective VIN shown.
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 57
WARRANTY INFORMATION:
REQUIRED TOOLS & EQUIPMENT:
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 58
PARTS INFORMATION:
REPAIR PROCEDURE:
1. Please compare customer's iPod(TM) with the compatible models table listed. If the customer's iPod(TM) is NOT listed, this TSB does NOT
apply.
2. Verify the condition.
NOTE
If USB device error occurs during every use, visually inspect port.
3. Verify the error condition continues when using a known good USB cable.
4. Replace the Multi-Media Interface ECU by following procedures in the repair manual. Refer to the Repair Manual within E-TAS / TIS library:
- Division: Lexus
- Model: Applicable Model
- Year: 2010
- Service Category: Audio/Visual/Telematics
- Section: Audio/Video
- Keyword: Multi-Media Interface ECU: Removal / Installation
5. Verify normal USB operation after repair.
NOTE:
Issue of this Technical Service Bulletin is to ensure that proper repair information is available. IT DOES NOT CONSTITUTE AN
AUTHORIZATION FOR REPAIR. Normal provisions of the formal warranty policy, as applicable, will apply.Technical Service
Bulletin # CAN-TSB2838L Date: 100831
Canada - Body - Rear Bumper Cover Gaps Develop
Bulletin
TSB2838
Issue Date
August 31, 2010
Title
REAR BUMPER COVER POOR FIT
Component
BODY
Models
'10 RX350; RX450h
INTRODUCTION:
Some 2010 model year RX350 and RX450h models may exhibit a condition where a gap develops at the left and/or right corners of the rear bumper
cover. This condition may occur more frequently in high ambient temperatures. An improved bumper cover and support have been developed to
correct this condition.
Follow the procedure in this bulletin to install the improved bumper cover and supports.
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 59
APPLICABILITY:
PRODUCTION CHANGE INFORMATION:
This TSB applies to vehicles produced BEFORE the Production Change Effective VIN shown.
WARRANTY INFORMATION:
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 60
PARTS INFORMATION:
REQUIRED TOOLS & EQUIPMENT:
TSB OVERVIEW:
This TSB provides an inspection and rear bumper cover replacement procedure to correct excessive gaps at the corners of the rear bumper.
REPAIR PROCEDURE:
1. Confirm that the rear bumper cover is loose at either the left and/or right side corner(s), below the taillight assembly as shown in Figure 1.
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 61
A. If the rear bumper cover is loose, proceed to step 2 of the procedure.
B. If the rear bumper cover is NOT loose, STOP.
This TSB does NOT apply.
2. Remove No. 2 luggage compartment side cover protector.
A. Remove the 2 screws and grommet.
B. Remove the 4 screws, 2 Bolts and 3 Clips.
C. Disengage the 2 claws and remove the No. 2 luggage compartment side cover protector.
3. Remove the No. 1 luggage compartment side cover protector.
A. Remove the 2 bolts and 2 screws.
B. Remove the 2 clips and No. 1 luggage compartment side cover protector.
4. Remove rear bumper assembly.
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 62
A. Put protective tape around the rear bumper assembly.
B. Using a clip remover, remove the 2 clips.
C. Remove the 2 screws and 2 rear bumper upper stoppers.
D. Remove the screw.
HINT
Use the same procedure for the RH side and LH side.
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 63
E. Disengage the 7 claws.
HINT
Use the same procedure for the RH side and LH side.
F. Disconnect the No. 3 luggage room wire harness connector.
G. Disengage the 4 claws and 4 guides, and remove the rear bumper assembly as shown in the illustration.
5. Remove both the left and right side rear bumper supports and discard.
A. Remove the 2 screws.
B. Disengage the 2 claws and remove the rear bumper side supports and discard.
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 64
6. Send the vehicle to the body shop for painting and finishing of the new bumper cover.
Refer to the Technical Information System (TIS), and the following manuals:
- Lexus Fundamental Body Repair Procedures manual
- Complete set of Lexus Collision Repair manuals
7. Transfer components from original bumper cover to new bumper cover,Refer to the Repair Manual within E-TAS / TIS library:
- Division: Lexus
- Model: RX350
- Year: 2010
- Service Category: Vehicle Exterior
- Section: Exterior Panels/Trim
- Keyword: Rear Bumper: Disassembly / Reassembly
8. Install the New left and right side rear bumper supports.
A. Engage the 2 claws.
B. Install the rear bumper side support LH with the 2 screws.
Torque: 7.5 N-m (77 kgf-cm, 66 in-lbf)
HINT
Use the same procedure for the RH side and LH side.
9. Install rear bumper assembly.
A. Connect the No. 3 luggage room wire harness connector.
B. Engage the 4 claws and 4 guides, and install the rear bumper assembly as shown in the illustration.
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 65
C. Engage the 7 claws.
HINT
Use the same procedure for the RH side and LH side.
D. Install the screw.
Torque: 2.5 N-m (26 kgf-cm, 22 in-lbf)
HINT
Use the same procedure for the RH side and LH side.
E. Engage the 2 rear bumper upper stoppers and install the 2 screws.
Torque: 7.5 N-m (77 kgf-cm, 66 in-lbf)
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 66
F. Install the 2 clips.
10. Confirm fit and finish of rear bumper cover.
NOTE:
Issue of this Technical Service Bulletin is to ensure that proper repair information is available. IT DOES NOT CONSTITUTE AN
AUTHORIZATION FOR REPAIR. Normal provisions of the formal warranty policy, as applicable, will apply.Technical Service
Bulletin # CAN-TSB2811L Date: 100728
Canada - Interior - Front Center Console Side Inoperative
Bulletin
TSB2811
Issue Date
July 28, 2010
Title
FRONT CENTRE CONSOLE SLIDE INOPERATIVE
Component
BODY COMPONENTS
Models
'10 RX350, RX450h
INTRODUCTION:
Some 2010 model year RX350 and RX450h vehicles may exhibit a condition where the front centre console lid may be difficult to slide.
A revised Console Compartment Door Lock Assembly has been developed to improve this condition.
APPLICABILITY:
PRODUCTION CHANGE INFORMATION:
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 67
This TSB applies to vehicles produced BEFORE the Production Change Effective VIN shown.
WARRANTY INFORMATION:
PARTS INFORMATION:
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 68
REQUIRED TOOLS & EQUIPMENT:
REPAIR PROCEDURE:
1. Remove the Console Compartment Door Lock Sub-Assembly, No.1 Upper Box Plate and No. 2 Upper Box Plate. Refer to the Repair Manual
within E-TAS / TIS library:
- Division: Lexus
- Model: RX350/RX450h
- Year: 2010
- Service Category: Vehicle Interior
- Section: Interior Panels/Trim
- Keyword: Front Console Box: Disassembly
2. Install the New Console Compartment Door Lock Sub-Assembly, No.1 Upper Box Plate and No. 2 Upper Box Plate. Refer to the Repair Manual
within E-TAS / TIS library:
- Division: Lexus
- Model: RX350/RX450h
- Year: 2010
- Service Category: Vehicle Interior
- Section: Interior Panels/Trim
- Keyword: Front Console Box: Reassembly
3. Confirm front console box lock operation.
NOTE:
Issue of this Technical Service Bulletin is to ensure that proper repair information is available. IT DOES NOT CONSTITUTE AN
AUTHORIZATION FOR REPAIR. Normal provisions of the formal warranty policy, as applicable, will apply.
2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 69
No comments:
Post a Comment