Showing posts with label (g) Rapidly reduce the tire pressure for each wheel by at least 40 kPa (0.4 kgf/cm2. Show all posts
Showing posts with label (g) Rapidly reduce the tire pressure for each wheel by at least 40 kPa (0.4 kgf/cm2. Show all posts

Thursday, August 8, 2019

2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 367


(g) Rapidly reduce the tire pressure for each wheel by at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds. If the "ID Tire Inflation



Pressure" data displayed on the tester (ID1 to ID5) does not change, the tire pressure warning valve and transmitter corresponding to



the unchanged "ID Tire Inflation Pressure" data was the cause of the output DTC.



HINT



* Identify the malfunctioning tire pressure warning valve and transmitter by repeatedly decreasing the tire pressure for each



tire.



* Record which "ID Tire Inflation Pressure" data (ID1 to ID5) corresponds to which tire.



Tire Pressure Monitor



HINT



*: It may take about 2 or 3 minutes until the values are displayed. If the values are not displayed after a few minutes, perform



troubleshooting according to the inspection procedure for DTCs C2121/21 to C2125/25 See: C Code Charts/C2121.



(h) Check the DATA LIST.



Result:



NOTICE:



* When the "ID Tire Inflation Pressure" data has not changed, reset the tire pressure to the appropriate specified value and



rotate the tire 90 to 270锟斤拷. Then rapidly release the tire pressure and recheck the data.



* Record the transmitter IDs and positions of transmitters that are normal.



(i) When the "ID Tire Inflation Pressure" data (ID1 to ID5) has changed, repeat this procedure to identify the tire pressure warning valve



and transmitter that corresponds to the DTC.



(j) When all of the "ID Tire Inflation Pressure" data (ID1 to ID5) has changed, identify the malfunctioning tire pressure warning valve

Saturday, July 20, 2019

2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 792


(g) Rapidly reduce the tire pressure for each wheel by at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds.



(h) Check the DATA LIST.



NOTICE:



* It takes about 2 or 3 minutes to display the updated tire pressure data.



* When the "ID Tire Inflation Pressure" data has not changed, reset the tire pressure to the appropriate specified value and



rotate the tire 90 to 270锟斤拷. Then rapidly release the tire pressure and recheck the data.



* Record the "ID Tire Inflation Pressure" data transmitter ID that corresponds to each tire.



(i) After confirming that the "ID Tire Inflation Pressure" data for one tire (ID1 to ID5) has changed, repeat this procedure one by one.



Identify the transmitter that corresponds to the DTC.



Result:



C -- END



B -- CHECK TRANSMITTER ID



A -- Continue to next step.



4. CHECK HARNESS AND CONNECTOR (ECU - RECEIVER)



(a) Disconnect the F53 ECU connector.



(b) Disconnect the P34 receiver connector.



(c) Measure the resistance according to the value(s) in the table below.



Standard resistance:



Text in Illustration



NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR



OK -- Continue to next step.

Monday, June 10, 2019

2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 236


(g) Rapidly reduce the tire pressure for each wheel by at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds.



(h) Check the DATA LIST.



NOTICE:



* It takes about 2 or 3 minutes to display the updated tire pressure data.



* When the "ID Tire Inflation Pressure" data has not changed, reset the tire pressure to the appropriate specified value and



rotate the tire 90 to 270锟斤拷. Then rapidly release the tire pressure and recheck the data.



* Record the "ID Tire Inflation Pressure" data transmitter ID that corresponds to each tire.



(i) After confirming that the "ID Tire Inflation Pressure" data for one tire (ID1 to ID5) has changed, repeat this procedure one by one.



Identify the transmitter that corresponds to the DTC.



Result:



C -- END



B -- CHECK TRANSMITTER ID



A -- Continue to next step.



4. CHECK HARNESS AND CONNECTOR (ECU - RECEIVER)



(a) Disconnect the F53 ECU connector.



(b) Disconnect the P34 receiver connector.



(c) Measure the resistance according to the value(s) in the table below.



Standard resistance:



Text in Illustration



NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR



OK -- Continue to next step.

Thursday, April 18, 2019

2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 218


(g) Rapidly reduce the tire pressure for each wheel by at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds.



(h) Check the DATA LIST.



NOTICE:



* It takes about 2 or 3 minutes to display the updated tire pressure data.



* When the "ID Tire Inflation Pressure" data has not changed, reset the tire pressure to the appropriate specified value and



rotate the tire 90 to 270锟斤拷. Then rapidly release the tire pressure and recheck the data.



* Record the "ID Tire Inflation Pressure" data transmitter ID that corresponds to each tire.



(i) After confirming that the "ID Tire Inflation Pressure" data for one tire (ID1 to ID5) has changed, repeat this procedure one by one.



Identify the transmitter that corresponds to the DTC.



Result:



C -- END



B -- CHECK TRANSMITTER ID



A -- Continue to next step.



4. CHECK HARNESS AND CONNECTOR (ECU - RECEIVER)



(a) Disconnect the F53 ECU connector.



(b) Disconnect the P34 receiver connector.



(c) Measure the resistance according to the value(s) in the table below.



Standard resistance:



Text in Illustration



NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR



OK -- Continue to next step.

Monday, April 1, 2019

2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 251


(g) Rapidly reduce the tire pressure for each wheel by at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds.



(h) Check the DATA LIST.



NOTICE:



* It takes about 2 or 3 minutes to display the updated tire pressure data.



* When the "ID Tire Inflation Pressure" data has not changed, reset the tire pressure to the appropriate specified value and



rotate the tire 90 to 270锟斤拷. Then rapidly release the tire pressure and recheck the data.



* Record the "ID Tire Inflation Pressure" data transmitter ID that corresponds to each tire.



(i) After confirming that the "ID Tire Inflation Pressure" data for one tire (ID1 to ID5) has changed, repeat this procedure one by one.



Identify the transmitter that corresponds to the DTC.



Result:



C -- END



B -- CHECK TRANSMITTER ID



A -- Continue to next step.



4. CHECK HARNESS AND CONNECTOR (ECU - RECEIVER)



(a) Disconnect the F53 ECU connector.



(b) Disconnect the P34 receiver connector.



(c) Measure the resistance according to the value(s) in the table below.



Standard resistance:



Text in Illustration



NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR



OK -- Continue to next step.

Wednesday, March 27, 2019

2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 820


(g) Rapidly reduce the tire pressure for each wheel by at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds.



(h) Check the DATA LIST.



NOTICE:



* It takes about 2 or 3 minutes to display the updated tire pressure data.



* When the "ID Tire Inflation Pressure" data has not changed, reset the tire pressure to the appropriate specified value and



rotate the tire 90 to 270锟斤拷. Then rapidly release the tire pressure and recheck the data.



* Record the "ID Tire Inflation Pressure" data transmitter ID that corresponds to each tire.



(i) After confirming that the "ID Tire Inflation Pressure" data for one tire (ID1 to ID5) has changed, repeat this procedure one by one.



Identify the transmitter that corresponds to the DTC.



Result:



C -- END



B -- CHECK TRANSMITTER ID



A -- Continue to next step.



4. CHECK HARNESS AND CONNECTOR (ECU - RECEIVER)



(a) Disconnect the F53 ECU connector.



(b) Disconnect the P34 receiver connector.



(c) Measure the resistance according to the value(s) in the table below.



Standard resistance:



Text in Illustration



NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR



OK -- Continue to next step.

Thursday, March 21, 2019

2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 848


(g) Rapidly reduce the tire pressure for each wheel by at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds.



(h) Check the DATA LIST.



NOTICE:



* It takes about 2 or 3 minutes to display the updated tire pressure data.



* When the "ID Tire Inflation Pressure" data has not changed, reset the tire pressure to the appropriate specified value and



rotate the tire 90 to 270锟斤拷. Then rapidly release the tire pressure and recheck the data.



* Record the "ID Tire Inflation Pressure" data transmitter ID that corresponds to each tire.



(i) After confirming that the "ID Tire Inflation Pressure" data for one tire (ID1 to ID5) has changed, repeat this procedure one by one.



Identify the transmitter that corresponds to the DTC.



Result:



C -- END



B -- CHECK TRANSMITTER ID



A -- Continue to next step.



4. CHECK HARNESS AND CONNECTOR (ECU - RECEIVER)



(a) Disconnect the F53 ECU connector.



(b) Disconnect the P34 receiver connector.



(c) Measure the resistance according to the value(s) in the table below.



Standard resistance:



Text in Illustration



NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR



OK -- Continue to next step.

Wednesday, February 13, 2019

2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 182


(g) Rapidly reduce the tire pressure for each wheel by at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds.



(h) Check the DATA LIST.



NOTICE:



* It takes about 2 or 3 minutes to display the updated tire pressure data.



* When the "ID Tire Inflation Pressure" data has not changed, reset the tire pressure to the appropriate specified value and



rotate the tire 90 to 270锟斤拷. Then rapidly release the tire pressure and recheck the data.



* Record the "ID Tire Inflation Pressure" data transmitter ID that corresponds to each tire.



(i) After confirming that the "ID Tire Inflation Pressure" data for one tire (ID1 to ID5) has changed, repeat this procedure one by one.



Identify the transmitter that corresponds to the DTC.



Result:



C -- END



B -- CHECK TRANSMITTER ID



A -- Continue to next step.



4. CHECK HARNESS AND CONNECTOR (ECU - RECEIVER)



(a) Disconnect the F53 ECU connector.



(b) Disconnect the P34 receiver connector.



(c) Measure the resistance according to the value(s) in the table below.



Standard resistance:



Text in Illustration



NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR



OK -- Continue to next step.

Tuesday, January 8, 2019

2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 863


(g) Rapidly reduce the tire pressure for each wheel by at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds.



(h) Check the DATA LIST.



NOTICE:



* It takes about 2 or 3 minutes to display the updated tire pressure data.



* When the "ID Tire Inflation Pressure" data has not changed, reset the tire pressure to the appropriate specified value and



rotate the tire 90 to 270锟斤拷. Then rapidly release the tire pressure and recheck the data.



* Record the "ID Tire Inflation Pressure" data transmitter ID that corresponds to each tire.



(i) After confirming that the "ID Tire Inflation Pressure" data for one tire (ID1 to ID5) has changed, repeat this procedure one by one.



Identify the transmitter that corresponds to the DTC.



Result:



C -- END



B -- CHECK TRANSMITTER ID



A -- Continue to next step.



4. CHECK HARNESS AND CONNECTOR (ECU - RECEIVER)



(a) Disconnect the F53 ECU connector.



(b) Disconnect the P34 receiver connector.



(c) Measure the resistance according to the value(s) in the table below.



Standard resistance:



Text in Illustration



NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR



OK -- Continue to next step.

Saturday, December 29, 2018

2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 160


(g) Rapidly reduce the tire pressure for each wheel by at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds.



(h) Check the DATA LIST.



NOTICE:



* It takes about 2 or 3 minutes to display the updated tire pressure data.



* When the "ID Tire Inflation Pressure" data has not changed, reset the tire pressure to the appropriate specified value and



rotate the tire 90 to 270锟斤拷. Then rapidly release the tire pressure and recheck the data.



* Record the "ID Tire Inflation Pressure" data transmitter ID that corresponds to each tire.



(i) After confirming that the "ID Tire Inflation Pressure" data for one tire (ID1 to ID5) has changed, repeat this procedure one by one.



Identify the transmitter that corresponds to the DTC.



Result:



C -- END



B -- CHECK TRANSMITTER ID



A -- Continue to next step.



4. CHECK HARNESS AND CONNECTOR (ECU - RECEIVER)



(a) Disconnect the F53 ECU connector.



(b) Disconnect the P34 receiver connector.



(c) Measure the resistance according to the value(s) in the table below.



Standard resistance:



Text in Illustration



NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR



OK -- Continue to next step.

Saturday, December 15, 2018

2010 Lexus Truck RX 350 AWD V6-3.5L (2GR-FE) Page 737


(g) Rapidly reduce the tire pressure for each wheel by at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds.



(h) Check the DATA LIST.



NOTICE:



* It takes about 2 or 3 minutes to display the updated tire pressure data.



* When the "ID Tire Inflation Pressure" data has not changed, reset the tire pressure to the appropriate specified value and



rotate the tire 90 to 270锟斤拷. Then rapidly release the tire pressure and recheck the data.



* Record the "ID Tire Inflation Pressure" data transmitter ID that corresponds to each tire.



(i) After confirming that the "ID Tire Inflation Pressure" data for one tire (ID1 to ID5) has changed, repeat this procedure one by one.



Identify the transmitter that corresponds to the DTC.



Result:



C -- END



B -- CHECK TRANSMITTER ID



A -- Continue to next step.



4. CHECK HARNESS AND CONNECTOR (ECU - RECEIVER)



(a) Disconnect the F53 ECU connector.



(b) Disconnect the P34 receiver connector.



(c) Measure the resistance according to the value(s) in the table below.



Standard resistance:



Text in Illustration



NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR



OK -- Continue to next step.